Speed Bumps
How Much Do Speed Bumps Cost? 2026 Pricing Breakdown
Cojo
May 7, 2026
7 min read
A typical speed bump installation in Oregon runs $200 to $1,500 per bump. The spread depends on material, length, anchor type, and how messy the site is. Recycled rubber sits at the low end. Cast-in-place asphalt and precast concrete sit at the high end. Multi-bump jobs usually shave 10 to 25 percent off because the mobilization fee gets spread across the whole project.
What's below: pricing broken out by material, by install type, and by site condition. Plus what 2026 market reality looks like and the line items that push a quote up or down.
Industry Baseline Range
| Material | Per-Unit Range (Material Only) | Installed Range (Per Bump) |
|---|---|---|
| Plastic (HDPE or PVC) | $40 to $200 | $150 to $500 |
| Recycled rubber (residential grade) | $80 to $200 | $150 to $400 |
| Recycled rubber (heavy-duty commercial) | $200 to $400 | $200 to $700 |
| Recycled rubber (industrial grade) | $300 to $500 | $300 to $900 |
| Cast-in-place asphalt | $0 (paved on site) | $300 to $1,500 |
| Precast concrete | $200 to $800 | $400 to $2,000 |
In 2026, speed bump install costs in Oregon have run 25 to 40 percent above 2024 baselines, driven by:
The only reliable way to know your actual cost is through an on-site assessment. For deeper material-specific breakdowns, see our rubber speed bump cost and speed bump installation cost guides.
Eleven factors typically drive a speed bump quote up or down:
The biggest single driver. Plastic is cheapest, rubber is next, asphalt is mid-range, concrete is highest. Heavy-duty rubber for commercial use roughly doubles the per-section cost of residential rubber. See our rubber speed bump vs asphalt and concrete speed bump vs asphalt comparisons for the trade-offs.
A 6-foot section costs roughly 40 percent more than a 4-foot section. End caps run an additional $80 to $200 each. Most lane-spanning installs use a 6 ft body plus a 2 or 3 ft cap.
Single-bump installs carry the full mobilization fee ($250 to $800+) on one unit. Multi-bump installs amortize mobilization across the project. A 5-bump install typically runs 15 to 25 percent less per unit than a 1-bump install.
Lag-bolt anchors in epoxy on sound asphalt or concrete are the standard at $30 to $80 per bump. Cracked or deteriorating pavement requires patching before anchor placement, adding $100 to $400 per bump. Concrete pavement requires masonry-bit drilling that runs slightly slower than asphalt drilling.
Yellow-and-black chevron paint runs $40 to $120 per bump. Thermoplastic markings (longer-lasting) run $80 to $250 per bump. Reflective tape is typically integrated with the rubber product but adds $20 to $60 if separate markers are needed.
A Manual on Uniform Traffic Control Devices W17-1 bump warning sign installed on a 2-inch steel post costs $200 to $500 per location. Most projects need at least one upstream sign per direction of travel.
Pole-mounted reflectors at $40 to $80 each are standard on commercial installs. Pavement-embedded reflective markers run $30 to $60 each.
A drive-up site with open lane access runs base labor. Tight retail centers with traffic-control needs (cone setup, flagging) add $300 to $1,200 per project. Active warehouse yards with operations coordination add $500 to $2,000.
Removing failed plastic or older rubber bumps runs $100 to $300 per location, plus patching the underlying anchor holes. Removing asphalt or concrete bumps runs $1,500 to $4,000 per location due to saw-cutting and patching.
Permits on public-property installs run $100 to $600 per project depending on jurisdiction. Prevailing-wage projects (public works, school district BOLI projects) typically add 30 to 60 percent to labor cost.
Flat fee covering crew travel, equipment dispatch, and project setup. Typical Oregon range is $250 to $800+ per project. Larger projects can negotiate this lower as a percentage of total.
| Project | Bumps | Material | Site | Estimated Range |
|---|---|---|---|---|
| Single-family driveway | 1 | Residential rubber 4 ft | Suburban driveway | $200 to $450 |
| Apartment complex drive aisle | 5 | HD commercial rubber 6 ft | Beaverton multifamily | $1,400 to $2,500 |
| Retail center pickup lane | 3 | HD commercial rubber 6 ft | Salem retail | $850 to $1,800 |
| Distribution-center inbound lane | 6 | Industrial rubber 6 ft | Hillsboro DC | $2,500 to $4,500 |
| HOA private road | 4 | HD commercial rubber 6 ft | Beaverton HOA | $1,100 to $2,000 |
| New parking-lot construction | 4 | Cast-in-place asphalt | Eugene retail center | $2,000 to $5,500 |
| Truck-terminal yard | 6 | Precast concrete | Tualatin freight | $4,000 to $11,000 |
A residential rubber bump install is within reach for a property owner with a hammer drill and a torque wrench. A 4-foot residential rubber section sourced directly from a manufacturer typically runs $80 to $200, and the installed-by-owner cost (not counting time) is $100 to $250 per bump including hardware, paint, and reflectors.
The DIY breakeven shifts when projects exceed 3 bumps, when paving operations are needed (asphalt or concrete bumps), when ADA reviews are required (commercial sites), or when Oregon Construction Contractors Board licensing is required for commercial work.
For a step-by-step DIY guide, see how to install speed bumps.
Cojo is a contractor and our specific quotes vary by project. Industry-baseline ranges above are what the broader market charges for similar work. We recommend an on-site evaluation for an exact quote because the 11 cost factors above all interact.
On a Portland medical-campus install in March 2026, we placed four heavy-duty 6-foot rubber sections along the patient-pickup lane plus two W17-1 advance-warning signs and integrated reflectors. The total project landed at $1,520 ($380 per bump average including signage and mobilization). For broader local context including service-area coverage, see our speed bump installation in Portland page.
Cojo also handles full-scope installs paired with asphalt maintenance services when bumps coincide with paving, sealcoat, or crack-fill work.
A simple budgeting framework:
A 5-bump apartment-complex install in 2026 budgets to roughly $1,800 to $3,000 using this framework. A 10-bump distribution-center install budgets to roughly $4,000 to $7,500.
A practical guide to sealcoating apartment and condo parking lots. Covers phased scheduling, tenant communication, cost allocation, liability, and ROI for property value.
Get accurate 2026 asphalt paving costs for Oregon driveways, parking lots, and roads. Per-square-foot pricing, cost factors, and money-saving tips.
Compare asphalt and concrete driveways side by side: cost, durability, maintenance, appearance, and climate performance for Oregon homes.
Have a question about this topic? We'll respond within 24 hours.